The effect of porosity on the laser induced damage threshold of TiO2 and ZrO2 single layer films

Monolayer ZrO₂ and TiO₂ films were prepared on BK7 glass by physical vapor deposition (PVD) and were subsequently annealed for 1 h at 300 °C. By using the transmission spectra of two samples and the envelope method, the refractive index dispersion and extinction coefficients have been calculated. Laser induced damage threshold (LIDT) measurement shows that despite slight differences between the extinction coefficients of the two samples, the LIDT parameter of the ZrO₂ film is greater than that of the TiO₂ film. This fact leads us to consider thermal conductivity as an important parameter for interpreting the LIDT difference. According to our theoretical analysis, as a consequence of increase in the number of thermal barriers along poorer film, its thermal conductivity, and hence LIDT, decreased, which is in agreement with our experimental results. The measured porosity of the two samples shows higher porosity for TiO₂ single layer, which is in agreement with atomic force (AFM) images. The gradual and smooth damage morphology of ZrO₂ observed in optical images implies higher thermal conductivity than TiO₂.     

辉光放电质谱分析中质谱干扰及其校正方法的现状

详细地介绍了辉光放电质谱分析中的质谱干扰如同量异位素、多原子离子和多电荷离子干扰。从同位素选择、高分辨率仪器、碰撞诱导解离、离子源冷却、数学方法校正、放电气体更换和放电气体纯度提高等方面对辉光放电质谱的质谱干扰校正方法的现状进行了评述(引用文献共68篇)。     

Sampling and analytical framework for routine environmental monitoring of organic pollutants

Dubious data would lead to incorrect interpretations and consequently faulty conclusions. Environmental monitoring results therefore have to be unambiguous to avoid misunderstanding the problems under investigation. Representative sampling and appropriate laboratory procedures are keys to acquiring quality data in order to draw unbiased conclusions.Although a large number of studies on organic pollutants have been published, few efforts have been directed towards instituting a systematic framework from sampling design to instrumental analysis. Generally, the main components in such a framework should include sampling design, sample preparation, sample extraction, extract purification and fractionation, and quantification (including qualitative and quantitative analyses).This review outlines the sampling and analytical framework appropriate for routine monitoring of organic pollutants, particularly persistent organic pollutants widely occurring in the environment. We emphasize statistically-based sampling schemes and quality-assurance and quality-control measures desirable for environmental monitoring programs.By way of demonstrating their importance, we especially review procedures for collecting unconventional environmental samples (e.g., human blood, breast milk, human hair, fish and bird tissues, and ice and snow) and analytical methods for typical emerging organic chemicals.     

Surface modified microarray chip and laser induced fluorescence microscopy to detect DNA cleavage

This work describes a quantitative method to detect DNA damage in the presence of Pb and Cd ions using a surface modified microarray chip and a laser induced fluorescence microscopy (LIFM). The detection was carried out by the immobilization of a single-stranded DNA oligomer, tagged with a Cy5 fluorophore on a polydimethylsiloxane (PDMS) microarray chip followed by LIFM. Sulfosuccinimidyl-4-(N-maleimidomethyl) cyclohexane-1-carboxylate (Sulfo-SMCC) was attached as a cross-linker via the formation of covalent amide bonds. Then, the single-stranded DNA oligomer containing Cy5 as a fluorophore and thiol functional groups at both terminals, was bonded to the linker by reaction with sulfhydryl group. As the DNA oligomers were reacted with metal ions of Pb and Cd, the un-cleaved DNA oligomers were quantitatively identified by monitoring Cy5 fluorescence. Cadmium showed a quenching constant of 0.84 in the Stern–Volmer plot, whereas lead gave 0.22, indicating that cadmium ions suppress fluorescence more than lead ions. When optimized, fluorescence reductions of 23% (± 2.1) for Pb and 25% (± 1.4) for Cd were observed in air and decreased to almost < 5.0% in a radical scavenger of 5 mM. The cleaved DNA was also confirmed by MALDI-TOF-MS. In result, this experimental method using a microarray chip with surface modification provided quantitative determination of DNA oligomer damage with reproducible results, significantly reduced sample volumes and analysis times.     

Classification of partially reflecting surfaces using photodetached electron spectrum

Photodetachment spectra of H^? near a partially reflecting surface is investigated by closed orbit theory. A reflection parameter K is introduced for the analysis of the photodetached‐electron spectrum. Factor K controls the spectra on the screen and strongly depends on the surface properties of a material. This parameter can effectively be used for the classification of surfaces using photodetachment microscopy. © 2010 Wiley Periodicals, Inc. Int J Quantum Chem, 2010     

Diagnosis of lubricating oil by evaluating cyanide and carbon molecular emission lines in laser induced breakdown spectra

To prevent engine failure it is essential to change lubricating oil regularly before it loses its protective properties. It is also necessary to monitor the physical and chemical conditions of the oil to reliably determine the optimum oil-change intervals. The present work focuses on studying evolution of the cyanide (CN) and carbon (C₂) molecular spectral emission lines in the laser induced breakdown spectra of lubricating oil as a function of its consumption. The intensities of these molecular bands have been taken as indicator of engine oil degradation at certain mileage. Furthermore, the percentage of decay of CN and C₂ integral intensity values at the corresponding mileage was calculated in order to relate it to the degree of consumption of the motor oil. Such percentage decay of the CN and C₂ integral intensities have been found to increase gradually with increasing mileage which is accompanied with increasing depletion of engine oil. The results of using LIBS technique in the present measurements proved that it is possible to have a direct, straightforward and easy method for prediction of lubricating oil degree of consumption. This may facilitate scheduling the proper time and/or mileage intervals for changing the oil to avoid any possibility of engine failure.     

Laser Ablation Molecular Isotopic Spectrometry: Parameter influence on boron isotope measurements

Laser Ablation Molecular Isotopic Spectrometry (LAMIS) was recently reported for optical isotopic analysis of condensed samples in ambient air and at ambient pressure. LAMIS utilizes molecular emissions which exhibit larger isotopic spectral shits than in atomic transitions. For boron monoxide ¹⁰BO and ¹¹BO, the isotopic shifts extend from 114 cm⁻¹ (0.74 nm) to 145–238 cm⁻¹ (5–8 nm) at the B²Σ⁺ (v = 0) → X²Σ⁺ (v = 2) and A²Π_i (v = 0) → X²Σ⁺ (v = 3) transitions, respectively. These molecular isotopic shifts are over two orders of magnitude larger than the maximum isotopic shift of approximately 0.6 cm⁻¹ in atomic boron. This paper describes how boron isotope abundance can be quantitatively determined using LAMIS and how atomic, ionic, and molecular optical emission develops in a plasma emanating from laser ablation of solid samples with various boron isotopic composition. We demonstrate that requirements for spectral resolution of the measurement system can be significantly relaxed when the isotopic abundance ratio is determined using chemometric analysis of spectra. Sensitivity can be improved by using a second slightly delayed laser pulse arriving into an expanding plume created by the first ablation pulse.     

Detection of explosives in traces by laser induced breakdown spectroscopy: Differences from organic interferents and conditions for a correct classification

With the aim to study and to improve LIBS capability for detecting residues of energetic compounds in air surrounding, nine types of explosives and some potential interferents, placed in small quantities on a metallic support, were interrogated by a laser. Shot-to-shot behavior of the line intensities relative to the sample constituents was studied. The detected plasma was not stoichiometric and the line intensities, as well as their ratios, were changing even for an order of magnitude from one sampling point to another, particularly in the case of aromatic compounds. We explained some sources of such LIBS signal's behavior and this allowed us to establish a data processing procedure, which leads to a good linearization among the data sets. In this way, it was possible to determine some real differences between the LIBS spectra from explosives and interferents, and to correlate them with molecular formulas, with some known pathways for the molecule's decomposition and with successive chemical reactions in the plasma. Number spectral parameters, which distinguish the each studied explosive from other organic materials, were also determined and compared with previously published results relative to percentages of correct classifications for the same explosives. Experimental conditions for reliable recognition of the explosives by LIBS in air are also suggested, together with the parameters that should be considered or discarded from the classification procedure.     

锥光干涉法表征偶氮苯侧链液晶聚合物的光致取向

采用偏光显微镜在平行光和锥光条件下对液晶聚合物膜内分子的取向排列状态进行了研究,不同取向状态的膜由线偏振光或圆偏振光照射偶氮苯侧链液晶聚合物得到。结果表明,液晶聚合物膜采用线偏振光照射时,偶氮苯介晶基元沿面排列,形成单相畴面内取向态。该取向态的锥光干涉图为位于视场中心的粗黑十字,旋转载物台小于10°,该干涉图即完全退出...     

EMI shielding and dynamic mechanical analysis of graphene oxide-carbon nanotube-acrylonitrile butadiene styrene hybrid composites

Carbon nanomaterials such as carbon nanotubes (CNTs), graphene and their hybrid have been studied extensively. Despite having excellent properties of CNTs and graphene have not yet been fully realized in the polymer composites. During fabrication agglomeration of CNTs and restacking of graphene is a serious concern that results in the degradation of properties of nanomaterials into the final composites. To improve the dispersion of CNTs and restacking graphene, in the present research work, we focused on the hybridization of graphene oxide and CNTs. Multiwalled carbon nanotubes (MWCNTs), functionalized carbon nanotubes (FCNTs), and graphene oxide-carbon nanotubes (GCNTs) reinforced acrylonitrile butadiene styrene (ABS) composites were prepared separately by vacuum filtration followed by hot compression molding. Further, dynamic mechanical analysis (DMA), and electromagnetic interference (EMI) shielding properties of ABS composites reinforced carbon nanofillers were investigated. The dynamic mechanical properties of polymers strongly depend on the adhesion of fillers and polymer, entanglement density of polymer chains in the presence of carbon fillers. The dynamic mechanical characteristics such as storage, loss modulus, and damping factor of prepared composites were significantly affected by the incorporation of MWCNTs, FCNTs, and GCNTs. Maximum EMI shielding effectiveness of −49.6 dB was achieved for GCNT-ABS composites which were highest compared to MWCNTs-ABS composites (−38.6 dB) and FCNTs-ABS composites (−36.7 dB) in the Ku band (12.4–18 GHz). These results depict the great potential of GCNTs-ABS composites to be used in various applications of efficient heat dissipative EMI shielding materials for electronic devices.